Low action on P09

Started by Bluesygirl, October 07, 2005, 11:29:08 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

I'm experiencing some noticable buzzing while playing my P09 burst. Is there a way that I can make an adjustment myself to slightly increase the string height, without having to take it to my luthier? Thanks.

Hey Bluesy,
All depends... You may just need a little more neck relief.  The Larrivee sight gives an explanation as to how to do this. 
http://www.larrivee.com/data/customerservice/faq.htm

www.frets.com can walk you through how to check neck relief and see if an adjustment is in order.  If Saddle hight is a problem you can always put a small shim under your saddle. 

However, if the buzz is new, I would guess you are experiencing some dryness due to the change in the climate.  If this is the case the best thing to do is make sure your humidity is in a safe range.  Lots of people will keep 2 saddles for different times of the year, but most perfer to keep their guitars in a more stable / controled environment. 

-josh
Larrivee P-03MT
Martin 00
Epiphone Bluesmaster

I switched to medium strings and loosened the truss rod a 1/4 turn when I was getting string buzz on the 5th and 6th string between frets 1 and 3 in standard tuning. I did this AFTER having it set-up and discussing possible adjustments with someone who has written many articles and books on guitars. This does increase the action down the neck. I may replace the saddle to raise the action on my parlor- it is too easy to play. :wacko:
He also explained the nuances of short scale guitars and they do have a tendency to buzz occasionally, low string tension.
I'm also getting a buzz on my OOO-50 when tuned to open D so I'm going to try the same thing.
Adjusting the truss rod is not a replacement for a correct set-up.
The Dude abides.


Thanks for the link to the site. The only thing is it doesn't say which direction (clockwise or counter-clockwise) is which for tightening/loosening truss rod.

Lefty-/loosey- righty/tighty!
The Dude abides.


Hey,

IF left is loosey and right is tighty, how does that relate to what its doing to the neck?  For example, is left goint to allow the neck to relax therefore the strings will be closer to the frets?

*******************
Larrivee` LV-10
Alvarez 5056 - Tree of Life
Takamine G Series 12 String
*******************

Loosening the nut will allow the strings to pull the neck forward, giving it more relief and the strings will be higher off the frets.

Tightening the nut will pull the neck back against the strings, taking the relief out and straightening the neck.

The article that Frank Ford at Frets.com did about neck relief is a very good place to start learning.

Steve  :GRN>

Thanks Hoffman for asking that. I had the same question.  I'll give it a try.

This is how i set my guitars up - first I use the truss rod to remove all relief from the neck and make it flat.  I use a straight edge to check the relief laying it from fret one to fret 12 or 14.  Next I measure the string height (nice tool for this at stew mac) at the 12th fret on the high e and the low e and adjust the saddle height so that I meet low/medium height stats  (see stew mac or other sources for these stats).  I think it is important to get your saddle height set correctly BEFORE you start messing with neck relief.  Finally, I use the truss rod to put just enough relief in the neck to eliminate buzzing when I play my normal playing style.  I measure the relief using a straight edge and feeler gauges to be sure its within normal specs, (see stew mac and other sources). 

I am no expert, far from it.  But this seems to work pretty well for me.  I do try to start out a new guitar with a professional set up and make sure that the luthier or tech check and adjusts the string height at the nut and levels the frets.

One thing to keep in mind is that changes in strings can affect action and buzzing. If you are not using mediums you might try that before you touch the neck. Moving from lights to mediums will put a little more relief in the neck.  I use mediums on my parlour.  They work very well - still very slinky, more slinky that lights on my OM. 

Have fun with it and go slow, don't make any big changes - when in doubt get some help.

There are other issues that can cause buzzing and if you are getting buzzing after setting things up to normal specs you might want to have a pro take a look at it.
Rob



Bourgeois Vintage OM
Larrivee D-05 MT

QuoteI think it is important to get your saddle height set correctly BEFORE you start messing with neck relief.

When you add relief you will add string height.  Put .010 relief in and your going to be looking at a higher action at the 12th fret.  You then will need to adjust the saddle again to get the string height or action your looking for.

Steve   :GRN>

Quote from: SteveK on October 10, 2005, 12:38:34 AM
When you add relief you will add string height. Put .010 relief in and your going to be looking at a higher action at the 12th fret. You then will need to adjust the saddle again to get the string height or action your looking for.

Steve :GRN>

Good point.  I'll start putting in the optimal neck relief, then set the saddle height.  Makes sense to me.
Rob



Bourgeois Vintage OM
Larrivee D-05 MT

Quote from: NRGD on October 07, 2005, 11:50:26 AM
I switched to medium strings and loosened the truss rod a 1/4 turn when I was getting string buzz on the 5th and 6th string between frets 1 and 3 in standard tuning. I did this AFTER having it set-up and discussing possible adjustments with someone who has written many articles and books on guitars. This does increase the action down the neck. I may replace the saddle to raise the action on my parlor- it is too easy to play. :wacko:
He also explained the nuances of short scale guitars and they do have a tendency to buzz occasionally, low string tension.
I'm also getting a buzz on my OOO-50 when tuned to open D so I'm going to try the same thing.
Adjusting the truss rod is not a replacement for a correct set-up.

I had no intention of teaching anyone set-up I was addressing the original question. Which was:

Quote from: Bluesygirl on October 07, 2005, 11:29:08 AM
I'm experiencing some noticeable buzzing while playing my P09 burst. Is there a way that I can make an adjustment myself to slightly increase the string height, without having to take it to my luthier? Thanks.

Set-up should be done professionally if the owner has no experience, I even have my guitar's set-up checked again if I change string gauge.
That said:
Try using medium strings. These parlors sound great with mediums and with the short scale they are much easier to play than on a standard scale guitar. The added string tension will pull the neck forward increasing the action.
If you are experiencing a slight buzz between frets 1 and 3-5 loosening (turn the wrench left) the truss rod no more than 1/4 turn should take care of the problem. If not then the guitar should be checked by a professional.

Why do I make such a big deal about this? I once knew a twelve-year-old kid who wanted nothing more than to play guitar, that is all he thought about. Christmas comes around and he receives an acoustic guitar he tries to play it sounds like crap practices and practices still sounds like crap, decides he doesn't have what it takes to play guitar, quits.
Thirty-three years later decides to try again and realizes what his problem was at twelve, the guitar was set-up badly.
Now the first thing I do with a guitar is get it set-up professionally.
The Dude abides.


Quote from: NRGD on October 10, 2005, 11:45:52 AM

Thirty-three years later decides to try again and realizes what his problem was at twelve, the guitar was set-up badly.

A 1969 D-28 Martin perchance?  -_-
Randy R., Georgia, USA
Opinions available. Inquire about qty discount.
Forum Guitar III LS03 #15 ser no 108519

A slight bit of adjustment righty tighty has done the trick. My only complaint is that it is NOT easy to line up the truss rod tool because you cannot see where it goes inside the soundhole!

If you set a small makeup mirror inside the guitar so that it shows the truss rod end (I have one that folds up, so it can be adjusted where it hinges at an angle), and position the guitar so that the room light illuminates the mirror, it is much easier. Getting someone to hold a flashlight in combination with the mirror works well, too.

Deb
Larrivee OM-03PA
Larrivee Parlor 01K
Taylor 412e-R

Quote from: Bluesygirl on October 10, 2005, 08:17:25 PM
A slight bit of adjustment righty tighty has done the trick. My only complaint is that it is NOT easy to line up the truss rod tool because you cannot see where it goes inside the soundhole!

Sorry should have warned you about that too, I use a dental mirror from work to line it up. Sometimes you also have to back the adjusting wrench off a bit to remove it.
The Dude abides.


Powered by EzPortal