Main Forums => Technical Discussion => Topic started by: sawdustdave on July 29, 2013, 12:51:35 PM

Title: Installing a K&K
Post by: sawdustdave on July 29, 2013, 12:51:35 PM
It's not here, yet, but I'll be installing it into my OM-03Deluxe. I took a look at the guitar's end pin, and see that it's attached via a hex screw. Taking it off won't be a problem. What I'm looking for are suggestions for drilling the hole for the pickup. Note: I have a pretty complete woodworking shop and have a lot of experience with them. Also, I've rebuilt my share of computers (including tearing down drives and putting them back together). But this is my Larrivee - I don't want any mistakes.

And, no, I don't trust any local luthier I've heard of in the area. Bad experiences, and GC techs. I trust myself more, mainly because I care.

Thanks!
'
Title: Re: Installing a K&K
Post by: tuffythepug on July 29, 2013, 12:54:04 PM
 /When you remove the endpin you will find that the hole is predrilled for a standard endpin jack.    K&K will fit just fine.
Also, here is a real good set of instructions with photos of the K&K installatiion.  Better than the instr. that come with the K&K.
Skip past the drilling part;  you won't need to drill your Larrivee.


http://frettech.com/kk/
Title: Re: Installing a K&K
Post by: Queequeg on July 29, 2013, 01:04:29 PM
^ just like he said.
It's gonna be just fine.
Title: Re: Installing a K&K
Post by: unclrob on July 29, 2013, 02:46:05 PM
One thing to add get a small dowel that you can use to help get the jack thru the endpin hole.The end of the dowel will need to be small enough to fit into the jadk.You can also tread a 1/4 inch jack thru the hole to also pull it thru.
Title: Re: Installing a K&K
Post by: sawdustdave on July 29, 2013, 03:04:03 PM
Thanks! That removes some fears from the process. I hope to get to this on the weekend - first have some things on the lathe that need to be done first, then a good shop clean before I bring the guitar out.
Title: Re: Installing a K&K
Post by: Queequeg on July 29, 2013, 03:13:06 PM
Quote from: unclrob on July 29, 2013, 02:46:05 PM
One thing to add get a small dowel that you can use to help get the jack thru the endpin hole.The end of the dowel will need to be small enough to fit into the jadk.You can also tread a 1/4 inch jack thru the hole to also pull it thru.
Right.
I use a chopstick. Works like a charm.  :thumb
Title: Re: Installing a K&K
Post by: tuffythepug on July 29, 2013, 04:14:38 PM
The dowell or chopstick will work fine.    I used the wire hook method shown on the frettech instructions:

"Run a wire (a plain G string works fine) through the 1/2" strap jack hole, put a slight 3/16" bend on the inside end and hook it onto one of the strap jack end holes. Using this jack "fish" wire, pull the jack through the guitar's strap jack body hole. Adjust the jack's body length for the best fit on your acoustic - this may mean test fitting the jack several times after adjusting the body length. When the fit is right, lock it on *tight*."

Title: Re: Installing a K&K
Post by: unclrob on July 29, 2013, 09:42:55 PM
Great way of doing it.I use nail polish as a lock tight for securing the nut,a little dab will do you.
Title: Re: Installing a K&K
Post by: AZLiberty on July 30, 2013, 12:17:55 AM
Quote from: tuffythepug on July 29, 2013, 12:54:04 PM
/When you remove the endpin you will find that the hole is predrilled for a standard endpin jack.    K&K will fit just fine.
Also, here is a real good set of instructions with photos of the K&K installatiion.  Better than the instr. that come with the K&K.
Skip past the drilling part;  you won't need to drill your Larrivee.


http://frettech.com/kk/


Just to clarify (because this will come up in somebody's search) only the newer larrivees with the 2-part metal endpin are pre-drilled.  Older ones, (like most of mine) came with strap buttons instead of endpins.



This one being newer will be just fine.


Title: Re: Installing a K&K
Post by: tuffythepug on July 30, 2013, 12:44:37 AM
Quote from: AZLiberty on July 30, 2013, 12:17:55 AM
Just to clarify (because this will come up in somebody's search) only the newer larrivees with the 2-part metal endpin are pre-drilled.  Older ones, (like most of mine) came with strap buttons instead of endpins.



This one being newer will be just fine.





that's correct.    I don't know exactly when they switched to the newer style but it has been several years at least.    For the older Larrivees that do not have a prep-drilled 1/2" hole the frettech instructions I linked in my earlier post  cover the proper way to drill out the existing strap pin holes to the proper size.   
Title: Re: Installing a K&K
Post by: Mr_LV19E on July 30, 2013, 11:30:21 AM
Quote from: AZLiberty on July 30, 2013, 12:17:55 AM
Just to clarify (because this will come up in somebody's search) only the newer larrivees with the 2-part metal endpin are pre-drilled.  Older ones, (like most of mine) came with strap buttons instead of endpins.



This one being newer will be just fine.




And then there is the even older models that didn't have a pin at all, or a hole.
Title: Re: Installing a K&K
Post by: AZLiberty on July 31, 2013, 10:00:35 PM
Quote from: Mr_LV19E on July 30, 2013, 11:30:21 AM
And then there is the even older models that didn't have a pin at all, or a hole.

Even some (moderately) newer ones.  My 1999 parlor has neither a hole nor a strap button at the endblock.
Title: Re: Installing a K&K
Post by: unclrob on August 01, 2013, 12:35:44 AM
Just remember NEVER EVER use a 1/2 inch paddle bit this will DAMAGE your guitar.If doing this job yourself get someone who knows what there doing with the right tools to do the job.Buy a hand reamer drill a starting hole using a drill bit the next size up from the end of the hand reamer.Then ream it out to the right size.