I've just recently discovered a very strange vibration coming from somewhere in/on/within my newer LV-03 and it's perplexing the heck out of me. I seem to only encounter it when picking notes in D7 formation in the 3,4 & 5th frets (like a C chord fingering). It happens when lifting my middle finger from the D string in the 4th fret and then proceeding thru a quick little hammer on back on the D string in the 4th fret followed by a quick add of my pinky finger on the same string in the 5th fret. I can't even accurately describe the "noise" that this brings forth. It's almost a harmonic sound, but it has the tonal quality of banging on a guide wire from a telephone pole. It sounds distant and has the quality of a symathetic vibration. I'm certain it is not technique in nature, but rather vibration oriented, and it is very disturbing. I've executed similar fingering on different frets/strings and nothing brings forth this wierd noise. I've essentially checked everything I could, short of a string change. I have encountered a couple of slightly loose pins in the preceeding weeks that needed to be set a bit firmer which also settled a few buzzing vibes I was getting. No good guitar techs in easy range here, either, unfortunately, so I'm looking at 100 miles for professional help, which I'll definitely seek if needed. This is a very disconcerting noise that is very audible. Could it be as simple as strings? It's still wearing the D'Addario EP's from the factory, but they still sound clean at this point. :?
My experience has been that odd vibrations like that end up being slightly loose hardware - in my case typically the strap button that never wants to stay tight. It's happened a few times and always stumps me for a while until I remember.
I've read about truss rods also creating similar odd noises - maybe try adjusting it a bit - loosen then tighten.
If you figure it out, please tell us what it was - I've got one on my open low E I can't track down either.
Like GGBB stated check for loose screw's and nuts on the tuners also check any strap buttons.If there is a pickup check for wire's that may be moving also check the jack inside there may be a loose washer.Make sure that the strings are seated correctly in the nut slots plus make sure that the slots are cut correctly.Wish I could help more but I wouldneed it in hand.You anywhere near Tallahassee, Fla?
I sure do appreciate the words of wisdom...still working through various "potential" causes. Everything seems tight...haven't tried the truss rod yet. And Rob, I'm way up here in Michigan or else you'd see me headin' up your path about now. Very frustrated, and can't even really accurately describe the sound I'm hearing. It's almost a humming sound...but a buzz, per say, as it lacks that distinct tonal quality (or dis-quality if you will...). It ain't right, I know that. I even tried every different pick I could find in the house on the outside chance but to no avail. Seems to be originating from the D string itself, and there's a slight yet discernable delay between the precise instant of lifting pressure from the string and the actual start of the strange sound. Then again, it's entirely possible that I'm completely nuts and/or making way too much out of this. All I know is that it is not what I would consider normal and it's loud enough to noticably clash with the particular melodic interval. Never heard anything like it coming from any guitars I've ever played.
Perhaps a wolf note harmonic? Sometimes a different make or gauge of strings will cure it....or move it to another fret! :roll
I like the "wolf note" suggestion! Except it sounds more like a tin turtle with a loose shell... :humour:
You have an 'E'model. Make sure that whatever spring is used to hold the battery in place is well damped. These can sing. Use a piece of sponge or something to make dang sure that nothing in that pre-amp is vibrating.
To rule out sympathetic vibration of the strings between tuners and nut, tie on a section of thick rubber band on each one independently. If you hear it go away, then you've found your culprit. Shouldn't happen with the headstock angled back and a properly sized nut slot, but this is another common area of sympathetic vibration showing up in the sound.
-Scott
...or just tell everyone you have the world's only Larrivée sitar. Keep it just to play Norwegian Wood on, and buy a new Larrivée on which to play everything else. :bgrin:
Seriously, good luck tracking it down. Personally I would try a fresh set of strings before any other kind of detective work.
I've been able to identify the problem finally, and it's being caused by an ever so slight fret buzz from the 6th fret. Now I'm curious as to why this problem just popped up out of nowhere and is seemingly limited to the 6th fret and only the D string. I want to say nut slot, but why just the 6th fret then? It's like my guitar has a dead spot. Now the search begins for a reputable tech.... :ohmy:
G#, huh?
(the dreaded "wolf tone (http://en.wikipedia.org/wiki/Wolf_tone)")
Doesn't have the wolf note characteristic, as it's that darn fret completely inhibiting any sustain and replacing it with a sound akin to a sandhill crane with laryngitis. This guitar has frequently produced the mysterious "Lab" note, however, as every time I pick it up and play my Lab comes and sits right next to me and very proudly displays her beautiful singing voice for me to enjoy. After a minute or so she goes and lies down and watches. I almost wish she'd sing a little more 'cause I think she sounds better than I do.... :guitar :rolleye:
Quote from: Queequeg on June 13, 2013, 07:50:25 AM
G#, huh?
(the dreaded "wolf tone (http://en.wikipedia.org/wiki/Wolf_tone)")
If it's just the G# then try playing Ab instead. That should fix it. :humour:
Glad you found the problem, in the mean time, lots of entertaining quips from the peanut gallery!
I had a similar problem recently (not on a Larrivee), turned out, one of the back braces had come loose at one end, just enough to cause this weird vibration overtone sound, but only on certain frequencies.
You can also try adding just a smig more relief,not a lot just a CH more.Question has the guitar been setup?
To answer Rob: No, it wasn't set up beyond the factory as it played great right out of the box...that is, at least until recently. I have talked to a local music store who offered their "guitar guy", and if he can't address it they suggested a true tech about 80 miles away with a good reputation work/knowledge wise, but a not so great rep for length of turn-around (can take way too long to actually do even minor work).
We shall see...
Thanks for all the helpful input...and all the foolish fun, too. It's all appreciated...really, I mean that. Honestly. It's been totally surreal. Far out.
How long has it been in house now?I have found that there isn't a brand of guitar that after a couple of weeks that didn't need to be setup.Which should include a fret dressing with recrown,nut slot adjustment,trussrod adjustment,action rechecked and all screw's and nuts on the tuners resnugged.
It's been in the house for 2 1/2 months or so and plucked and twanged mercilessly since. Guess I shoulda figgered, eh? :whistling:
Think of it this way,you now know more about the guitar and what you want out of it and you can instruct the tech better.After 2 1/2 months everything has settled in as well as your fingers and ears.As always I'm an email away for any help I can be,plus make sure you interview the tech that's is going to handle you baby.Things like how long have you been teching,what kinda skill's can you have some phone numbers of other's who you did work for.
Thanks Rob, please know it's appreciated.
Riverbend, see my recent post about getting your guitar setup. It's going to be the best thing you've done for it!
(my om-03 springs new life)-post :donut :donut
Thanks 3Dz...I did read that post of yours a while ago.
Well, went off to see the "guitar specialist/repair guy" at my local music store today. He fiddled with the truss rod, he unfiddled the truss rod...still the same crazy G# wolf toneishness. New strings (which I thought I'd try but do not like so far...D'Ad's in medium guage PB) made it much worse. He had the guitar instructor listen to it and he was stumped. So down the road I'll go when I can to see the nearest "real" guitar tech, which is about 75 miles away. The funniest thing though, is when we were all done and I found out that the "guitar specialist" doesn't actually play guitar. He's a DRUMMER!
(insert drummer/drool/leveling the stage joke here) He almost tried to pry the first pin out with his side cutters before I whoa-whoa'd him up real quick. I pretty much hovered from that point on. Chalk one up I guess.
Here's an interesting post about wolf tones: link (http://www.ask-a-luthier.com/questions/question_09.htm)
It might be worthwhile to try the suggestion about changing out the saddle.
Quote from: rockstar_not on June 07, 2013, 03:22:28 PM
You have an 'E'model. Make sure that whatever spring is used to hold the battery in place is well damped. These can sing. Use a piece of sponge or something to make dang sure that nothing in that pre-amp is vibrating.
To rule out sympathetic vibration of the strings between tuners and nut, tie on a section of thick rubber band on each one independently. If you hear it go away, then you've found your culprit. Shouldn't happen with the headstock angled back and a properly sized nut slot, but this is another common area of sympathetic vibration showing up in the sound.
-Scott
Did you rule out the pre-amp/battery holder, springs, etc. first? Then have you tried to make sure no sympathetic string vibration is happening via the rubber band method I described above?
I had a 9v battery holder 'sing' in a previous guitar. Rule that out first before you make your trek.
Quote from: rockstar_not on June 25, 2013, 07:47:51 PM
Did you rule out the pre-amp/battery holder, springs, etc. first? Then have you tried to make sure no sympathetic string vibration is happening via the rubber band method I described above?
I had a 9v battery holder 'sing' in a previous guitar. Rule that out first before you make your trek.
Yep...thanks, I did all that stuff. This has stumped a few folks. I've never heard anything like this before from any guitar. The medium gauge strings made it even worse, too. Much more noticable, in fact, sometimes when I'm playing it, it sounds like a whole series of ringing noises that live somewhere between the notes. Crazy stuff...I'm starting to think it's possessed!?
Update...sort of at least. Pretty much convinced that my guitar just has a "dead spot" if I had to choose a term. Perhaps a "phase cancelling harmonic" might be applied descriptively, as well. On the D string at G#, where the woo-woo-woo-ing of the sickly sandhill crane/rusty barn door is first noticeable, and then when combined with the open G string below, the harmonics are a total train wreck. Several dampening techniques, string changes, truss rod tweaks, nut and saddle examinations later, I'm left wondering if I'm at a point where nothing can be done. I've read so much about wolf tones that I hear them in my sleep (might be the coyotes across the river...). I've been offered a new saddle in my choice of tusq or bone and been advised by a well respected forum member to avoid bone due to potential conflicts with my under-saddle pick-up. If I do try a new saddle, it seems that I'd also be responsible for any costs involved in fitting related work for the new saddle, plus there's no guarantee that it would change anything . I wish I had a good way to record the noise and post it here. I assure you it would make most of you cringe and at least some of you cry...it's not a pleasant sound coming from what is otherwise a beautiful guitar. I have other guitars ranging from expensive to lower end and none of them have this issue. An interesting side note is that while in a local guitar shop last week I picked a lower end Taylor off the wall, didn't notice the model but it retailed just under $800, and it seemed to have the same issue. I've sampled about a dozen guitars of various brands others in stores and haven't heard anything similar until the Taylor. I'm pretty much at a loss right now as far as what, if anything, to do.
Stewart-MacDonald sells a tool for checking fret level as compared to the fret before and the after it may be a low spot and the string rotation could be effected.
A saddle swap is a cheap investment. I am not aware of any potential conflicts with my under-saddle pick-up and a bone saddle unless it isn't fitted properly. Keep the old saddle, of course.
A brace may have to be filed down to change the harmonics of the top.
Quote from: Queequeg on July 16, 2013, 10:24:25 AM
A saddle swap is a cheap investment. I am not aware of any potential conflicts with my under-saddle pick-up and a bone saddle unless it isn't fitted properly. Keep the old saddle, of course.
A brace may have to be filed down to change the harmonics of the top.
Maybe "conflict" wasn't the right word choice on my part...it was mentioned that the amplified sound of under-saddle bone has been less than stellar in that person's opinion...I can't remember verbatim...and it was offered very generously and as simply their opinion. All I know is that I wish my guitar sounded somewhat "normal" in that relatively high traffic area of the neck. And by the way, the "noise"...or whatever describes it, has been verified by dozens of other ears and fingers...virtually everyone who has heard or fingered the guitar.
Broken truss rod perhaps? In order to do what you describe, my opinion is that somewhere on your guitar, something is loose that shouldn't be loose. Finding it has eluded you so far.
I've heard of wolf notes but not sure I have heard one. Just for the sake of experiment, try muting all other strings but that one note and hear what happens. Or capo at that particular fret and play normally to hear what happens. Maybe expose the guitar to higher humidity for some time to see how it affects the sound. Tune up or down a half step or whole step and see if the wolf note changes or disappears. Just thinking....
I had a Simon & Patrick parlor for a while that had a buzz at a certain frequency that I could not figure out. One day I had it outdoors for a while in warm humid weather and the buzz began to lessen.
Hope you get it figured out.
Quote from: broKen on July 16, 2013, 01:42:50 PM
I've heard of wolf notes but not sure I have heard one. Just for the sake of experiment, try muting all other strings but that one note and hear what happens. Or capo at that particular fret and play normally to hear what happens. Maybe expose the guitar to higher humidity for some time to see how it affects the sound. Tune up or down a half step or whole step and see if the wolf note changes or disappears. Just thinking....
I had a Simon & Patrick parlor for a while that had a buzz at a certain frequency that I could not figure out. One day I had it outdoors for a while in warm humid weather and the buzz began to lessen.
Hope you get it figured out.
Thanks for the suggestions...tried all of the muting/tunings/capo here capo there stuff. Tried truss rod adjustments, vibration dampening, about everything short of replacing the nut or saddle and they've both been inspected and seem fine. We'll see what happens tonight playing outside in very high humidity...but I don't think that's going to do anything because it's already been exposed to higher than average humidity playing outside on several occasions. Nothing is loose internally. Just seems to crash tonally at that particular frequency, though with a capo on, the D string seems pretty dead everywhere up the neck. What should be sustain is instead just a slightly off-key, chiming vibrating crash. It's an otherwise beautiful sounding guitar. I'm going to pay to have the saddle changed and hope that that and some more time might lead me to a happy conclusion. Other than that, I'm stumped.
Did I read something wrong? The noise is coming off the 6th fret? And when you're hammering on the pinky it's only up to 5th fret? And 6th never really fretted? Sorry if I misread something. I just got excited for a minute when you said 6th string cause I thought it had just settled in and needed frets dressed a little, or 6th had lifted or whatever.
Quote from: flatlander on July 16, 2013, 07:52:51 PM
Did I read something wrong? The noise is coming off the 6th fret? And when you're hammering on the pinky it's only up to 5th fret? And 6th never really fretted? Sorry if I misread something. I just got excited for a minute when you said 6th string cause I thought it had just settled in and needed frets dressed a little, or 6th had lifted or whatever.
D string 4th fret, but it's not fret buzz at all, it's a dead chiming sound that comes from somewhere. Accentuated even more if the note is hammered. Also has a weird mutual non-sustain when played with the open G string below. Sounds similar to a string picked above the nut...got that dead sound.
OK, That G# thing, which would be 6th fret, threw me off. And as for that matter adjacent 1/2 step notes always sound bad when played together. G# against G. Well good luck. Those things can be weird and frustrating but I wouldn't give up that someone good can find cause. As far as bone vs synthetic saddle I think problems usually arise if bone in not consistant in make up, which synthetic usually is, and can cause inbalance in volume across strings. Good quality bone is not a problem for me. I prefer bone as much as anything because they last longer. I don't like any buzzing but want to get as low as possible. If I put synthetic on the hairy edge like that doesn't last as long before 1st and 2nd string in particular notch themselves in and buzz.
I've not been too clear on this at all...sorry...but it actually starts at F# and pretty much heard through the whole step to G#. I've been thinking F# some of the times I've been writing G#. I don't normally read what I type and I type poorly and those keys are right next to each other. I also often play the wrong notes, too, not just type them...
Quote from: unclrob on July 16, 2013, 10:14:47 AM
Stewart-MacDonald sells a tool for checking fret level as compared to the fret before and the after it may be a low spot and the string rotation could be effected.
This is my guess.