I'm hoping that someone here has dealt with this issue and has an answer.
The ebony pins that came with my Larrivee D-09 have slots that are too narrow to
accommodate Medium strings. I also have the same problem with my L-03WL
The only way that I've been able to put Mediums is to use Tusq Pins.
Is there a way to make the slots wider and deeper? or are there pins that are sold that way?
Thanks.
Its a major pain in the but and it would be best to buy other pins then to carve out the one's you have.
Quote from: rrgguitarman on May 04, 2010, 08:04:09 PM
I'm hoping that someone here has dealt with this issue and has an answer.
The ebony pins that came with my Larrivee D-09 have slots that are too narrow to
accommodate Medium strings. I also have the same problem with my L-03WL
The only way that I've been able to put Mediums is to use Tusq Pins.
Is there a way to make the slots wider and deeper? or are there pins that are sold that way?
Thanks.
I have a L with standard ebony pins and play mediums exclusively. I have absolutely no trouble with them. Pins are just there to push the string balls under the bridgeplate, aren't they?
Having the slotted pins helps to keep the string from cutting into the bridge wood.
:cop:Wait a couple of seconds before you begin your attack I'm old and seem to have something wrong with my leg this week,must be the humidity.
Quote from: unclrob on May 04, 2010, 10:29:55 PM
Its a major pain in the but and it would be best to buy other pins then to carve out the one's you have.
Hi Rob,
HOW?
Thanks.
Quote from: unclrob on May 04, 2010, 10:39:28 PM
Having the slotted pins helps to keep the string from cutting into the bridge wood.
:cop:Wait a couple of seconds before you begin your attack I'm old and seem to have something wrong with my leg this week,must be the humidity.
Bummer! Probably from that exquisite storehouse of knowledge so overflowing. Beyond what 2 humans could duplicate :beer :wave
You have to have incredable control with a dremal or a hand held wood carving tool.You need to build a jig to hold it in place while doing the work.You need to go VERY VERY SLOW,so you don't over do it.Best thing to do is replace them with one's that fit.
QuoteYou have to have incredable control with a dremal or a hand held wood carving tool
That leaves me out!
What are the right size?
Do different (manufacturer) fit the Larrivee and have larger slots?
Its never easy...
Thanks Rob
I'm not sure.I have been using tusq now for about 10 years and have no complaints.
Looks like Tusq is going to reign...
Thanks Rob
Quote from: unclrob on May 04, 2010, 10:39:28 PM
Having the slotted pins helps to keep the string from cutting into the bridge wood.
:? :? :?
On my long-gone 000-15S I used a sharp pen knife and whittled the ebony pins until they fit it correctly. Labor of love, I guess, and it worked out fine.
Better still to call Bob Colosi and order the correct sized pins.
QuoteBetter still to call Bob Colosi and order the correct sized pins.
I don't want to go down the bone route...too bright.
Thanks.
GA-ME I covered myself with my escape clause. :bgrin:
How many of the pins are too tight? You probably need to work on just one or two right? Did you put them back in the same holes they came out of?
:coffee :donut2 :donut :donut
Quote from: Mr_LV19E on May 05, 2010, 05:51:23 PM
How many of the pins are too tight? You probably need to work on just one or two right? Did you put them back in the same holes they came out of?
:coffee :donut2 :donut :donut
Two of the pins, E and A
I always change strings one at a time, so, yes, the way they came out.
My Larrivees are not too bright with Tusq but my Taylors don't really care for Tusq and I have the same problem with them (same size pins)
Maybe try a little sandpaper folded over to widen and deepen the slot, it may take a while to remove enough material but it's just two pins. I have never heard of them making different size slots for bigger strings but as usual I could be wrong. I have bought oversize pins but that was outside diameter.