Main Forums => Recording, Pickups, Live Sound, etc. => Topic started by: Hogtop on January 08, 2010, 09:28:41 AM

Title: Baggs I-Mix ?
Post by: Hogtop on January 08, 2010, 09:28:41 AM
 :coffee
Title: Re: Baggs I-Mix ?
Post by: Hogtop on January 08, 2010, 09:39:02 AM
Woops . Where did my question go?  Anyway enjoy the coffee.
I've got a no-cut I-Mix and was wondering about switching out the under saddle part of it to a passive soundhole Baggs M1. Would the jack of the M1 fit into the jack of the pre-amp on the I'Mix and would the I'Mix power the M1? The blend wheel just inside the sound hole should work the same. I just like the sound of my guitar better un-plugged without the element under the saddle and like the sound of the active M1 in a friend's OM. Thinking the blend of the I-Beam and the M1 would be great. So what do you think?
Thanks. Steve
Title: Re: Baggs I-Mix ?
Post by: ncognito on January 08, 2010, 10:16:50 AM
Hogtop--

I am very curious what others will say.  I had the I-mix installed in my Guild.  It worked great; I should have left well enough alone.  I decided to have my tech transplant the I-mix from the Guild to my Lowden.  The problem was that the Lowden has a split saddle and pinless bridge so he reccomended doing exactly what you suggested, switching out the under saddle component for the passive I-Beam.  Well, the result is that yes, it works with the same blending knob as before, but that the passive I-beam has very little presence now in the mix; regardless of how much I dial it in, it is dramatically overpowered.  I don't know if the guy installed it incorrectly, or if he should have used the active I-beam, or what.  I've tried adding my Radial J48 Active Direct Box into the chain hoping its phantom power would even the balance, but if there is improvement, I'm unable to detect it.  It is frustrating.  I've had one too many issues with this guy to go back so for the time being I'll just live with it.

For your situation with a typical saddle and pin bridge I'd guess that the operation would be much easier except that you, and I'm guessing here, would need a new saddle.  I've got to say that the stock I-mix sounded fantastic to me so I'm not sure why you'd want to change.  Then again, I do understand that it's all personal preference.

       DAVE
Title: Re: Baggs I-Mix ?
Post by: ncognito on January 08, 2010, 10:36:05 AM
I just wanted to add that my LSV11e has the no-cut I-mix.  I liked it so much that I had one put in the Guild which I should have left in the Guild.  I've gotten some nice comments when I've plugged the LSV11 in, 0ne fellow player said that it really capturing the woody tone of the guitar.

I seem to remember that a few others on the forum have substituted the I-beam, and were happy with the outcome so you might want to do a forum search rather than rely on my feeble powers of recollection.
       
      DAVE
Title: Re: Baggs I-Mix ?
Post by: JohnT on January 09, 2010, 05:35:47 AM
Here is a relevant thread from a while back.

http://www.larriveeforum.com/smf/index.php?topic=27756.0

John
Title: Re: Baggs I-Mix ?
Post by: Hogtop on January 09, 2010, 08:36:45 AM
Thanks for that thread John. Those are the thoughts I had as well.  It is not that I don't like the element componet of the I-Mix, I just like the tone that I get when  playing unplugged with a bone saddle when the USP is not in the bridge.  I'll get the M1-C3 cable and contact my friend to send me his M1 passive.