Main Forums => Recording, Pickups, Live Sound, etc. => Topic started by: melanie on July 01, 2009, 02:38:01 PM

Title: Bone saddle and UST
Post by: melanie on July 01, 2009, 02:38:01 PM
Hi,

I have a B-Band A2.2 AST/UST pup system in my L-03R . I have just replaced the factory fitted Tusk saddle with a bone one that I shaped from a blank. Up till now I have believed that the optimum saddle for a UST  has been a man made item like TUSK. Several sources state that bone can be of inconsistant density which will upset the string balance.This has now been shot down in flames because the difference in sound and level is tremendous. The new saddle gives a fuller frequency range with a higher output from the UST. I believe this is because the bone saddle has been polished and is more slippery, so it can move more easily within the bridge slot.
So, if you are having trouble with a UST it may be worth fully polishing a bone saddle if the output is a bit low  .
Mel
Title: Re: Bone saddle and UST
Post by: obe-wan on July 02, 2009, 06:46:10 AM
Gday Mel,

I found the same thing with my OM-03R. The bone is denser than the TUSQ so I think it transfers vibration to the UST better. Sounds better acoustically too. :wink:

Cheers, Scott.
Title: Re: Bone saddle and UST
Post by: Stephen Basil on July 02, 2009, 07:36:34 AM
Tusq is the biggest fraud perpetrated against the consumer since the introduction of the carob bean back in the eighties!

That's my rant.
Title: Re: Bone saddle and UST
Post by: rxblitzrx on July 03, 2009, 04:24:52 PM
I love my bone  :humour:

kidding.  seriously though, bone is definitely the way to go.  I wish Larrivee would offer bone upgrades as an option.  I'd highly consider using their 03 series, if so.  Otherwise, I don't mind dropping another 1.5 grand to get another Breedlove.
Title: Re: Bone saddle and UST
Post by: Zohn on July 10, 2009, 01:03:29 AM
Quote from: rxblitzrx on July 03, 2009, 04:24:52 PM
I love my bone  :humour:

:+1: That is funny... LOL  :roll :roll :roll
Title: Re: Bone saddle and UST
Post by: tadol on July 11, 2009, 11:03:26 AM
I know an awful lot of luthiers who could upgrade an -03 with nice bone nut and saddle for alot less than $1500  -

Tad
Title: Re: Bone saddle and UST
Post by: rxblitzrx on July 12, 2009, 03:59:35 PM
Quote from: tadol on July 11, 2009, 11:03:26 AM
I know an awful lot of luthiers who could upgrade an -03 with nice bone nut and saddle for alot less than $1500  -

Tad

sadly, i'm shy of luthiers.  i've never had a good experience with one doing the job right and i live in houston,tx!  you figure in a city this large there would be someone capable of doing the job right.  the only time i've had a job done properly is when i shipped my guitar all the way back to oregon and had Breedlove fix the mistakes of the local luthier.  that was a costly process since shipping guitars isn't cheap. 

even a simple task like shaving a saddle down properly seems easy enough, but seriously... i had an extra one made while my guitar was in oregon just so i wouldn't have to rely on luthiers down here.  as for pulling the nut off and replacing it with a bone nut?  wow.  if shaving a flat surface on the bottom of a saddle to +/- 5% of 1/64" is too hard, how can they cut proper string spacings and glue a new nut in?  no sir. not for me.  if the manufacturer isn't putting these in, then i'll shop somewhere else. 

wow, sorry to rant.  i just realized i wrote a lot. don't get me wrong, i'm not trying to put luthiers down.  i would pay double just to find a competent luthier in my area, because it's more of a pain for me not to have one.  i'm just saying, in my experience you have to do everything yourself... or let the manufacturer do it... or buy handmade.