Main Forums => Larrivée Guitars => Topic started by: joopie on June 01, 2006, 10:59:22 PM

Title: pearse armrest?
Post by: joopie on June 01, 2006, 10:59:22 PM
wiskeyjack's thread got me thinkin' and the posts about the armrests...

i'm thinkin' i might get one (ebony) for my OM - any info/input on these- pros/cons, sizes, how are they attached- adhesive?

thanks,  :mellow: J.
Title: Re: pearse armrest?
Post by: joopie on June 02, 2006, 12:28:32 AM
ok- so i looked through some past threads and i think gonna go w/ the pearse slimline armrest- a lot of positive feedback on these- and i kinda like the look too...

:mellow: J.
Title: Re: pearse armrest?
Post by: whiskeyjack on June 02, 2006, 12:34:08 AM
There's a thin strip of adhesive tape on the outer edge of the Pearse arm rests.  I've never had to remove mine but my luthier tells me it's not that difficult.

The thinking is that these arm rests  decrease the damping effect your arm has on the movement of the sound board.  Everything from an increase in volume to better tasting popcorn has been cited as a benefit. ^_^  My experience with arm rests has been definitive. . . .on small guitars. 

I installed Pearse rests on my Taylor K12C and Larrivee 03R and I had my luthier make me one for my 000-15S.  There's nothing to installing them so long as you take the time to line them up as perfectly as possible with the binding on the lower bout.  Practice a couple times before you peel the backing off the tape because once it's down you don't want to remove it - the adhesive won't stick as tightly after the first time around.

I'm not convinced that arm rests are a benefit to larger guitars where the top and box are considerably larger.  The do look cool though -_- 

On my guitars I'm certain that I hear an increase in volume and projection.  They didn't seem to affect the voice of the instruments.  If you routinely use sound reinforcement of some kind, arm rests don't make a lot of sense.

Hope this helps.
Title: Re: pearse armrest?
Post by: joopie on June 02, 2006, 12:40:28 AM
thanks wiskeyjack- yep i was reading through some old threads and noted it had adhesive strip- and most folks seem to feel they have made a difference in more ways than one- i'm havin' fun w/ the idea of adding this detail to my OM-03- had bone and ebony added not to long ago- along w/ a good set up- really lovin this guitar!

:mellow: J.
Title: Re: pearse armrest?
Post by: sacredground on June 02, 2006, 09:10:35 AM
Glad you like your OM!

Looking through the previous posts on this topic, I found a very helpful hint. If for some reason you need to remove your arm reast, using dental floss between the top and the stick stuff does the trick--rather that twisting or pulling on the top. I was so curious that I tried it...and it worked! :GRN>
Title: Re: pearse armrest?
Post by: bob_d on June 02, 2006, 09:52:19 AM
Checking out the Pearse site I came across several John Pearse bridge pin sets in bell-bronze, bone, and buffalo horn (as well as faux tortoise shell).

http://www.jpstrings.com/brnew.htm

Does anyone agree that bridge pins affect the amount of energy transmitted through the bridge? Even if they don't I'm tempted to buy those bronze beauties! I wonder if they fit Larrivee guitars?

Title: Re: pearse armrest?
Post by: Roman on June 02, 2006, 09:56:04 AM
I have them on all of my acoustics.  And one size does not fit all.  To get a proper fit, I had to reshape each one to fit the contour of each guitar.  Especially if you position them on the guitar in the best location for your arm.  The adhesive is a 3M double sided tape which can be removed with a little heat from a hair dryer and slowly lift . . . similar to removing a pickguard only a lot easier and no residue left behind.  I'll send you a photo of the one I cut out of the full size armrest that I customized for my 814.
Title: Re: pearse armrest?
Post by: Roman on June 02, 2006, 09:58:01 AM
Well, I can't send you the image since your email isn't listed . . .
Title: Re: pearse armrest?
Post by: joopie on June 02, 2006, 10:24:16 AM
Quote from: sacredground on June 02, 2006, 09:10:35 AM
Glad you like your OM!

Looking through the previous posts on this topic, I found a very helpful hint. If for some reason you need to remove your arm reast, using dental floss between the top and the stick stuff does the trick--rather that twisting or pulling on the top. I was so curious that I tried it...and it worked! :GRN>

yeah- i read that too- a good tip!

:mellow: J.
Title: Re: pearse armrest?
Post by: pigtown on June 02, 2006, 11:07:57 AM
John Pearse has some excellent products, especially strings.  John is a great guy, I know him from another forum.  But I guess I'm a purist when it comes to the armrest.  I can't put one of them on a guitar top.  I also prefer the clear pickguard, which may be a correlation to the no armrest policy.
Title: Re: pearse armrest?
Post by: bhika on June 02, 2006, 11:16:05 AM
I was going to buy one on impulse after hearing all this talk about them, but can't find anyone with a left handed model. Also the left hand version is not available in the slimline, only the original.

So much for the impulse buy.  :<>
Title: Re: pearse armrest?
Post by: joxter on June 02, 2006, 11:23:07 AM
I put an ebony Jr. on my OM-03, its a good fit.  I was resting my arm on the top due to the smaller body of the guitar.  I can hear the difference in volume and sustain.
Now I am trying to figure if I need one on my new D-03R and if so which one, the ebony to match the fingerboard/bridge or the rosewood to match the back/sides?
Title: Re: pearse armrest?
Post by: bhika on June 02, 2006, 11:55:03 AM
If any lefties looking for these I found them at FQMS.
Title: Re: pearse armrest?
Post by: Blue in VT on June 02, 2006, 02:25:00 PM
I'm expecting one of these today...slimline junior...which I will be attaching to my parlor...both for the sound improvement and to coverup a dinger on the lower bout. I'll report back on Monday as to my first impressions.

Blue
Title: Re: pearse armrest?
Post by: expatCanuck on June 02, 2006, 03:53:36 PM
Quote from: pigtown on June 02, 2006, 11:07:57 AM
...I can't put [an armrest] on a guitar top.  I also prefer the clear pickguard ...

Amen.  I'm saddened (if not shocked & appalled) by Larrivee's change to 'traditional' pickguards. <sigh>

- Richard
Title: Re: pearse armrest?
Post by: Denis on June 02, 2006, 04:00:32 PM
I'm gonna order one today for my OM.  I thing for the price, if it improves the sound that much, it's definitely worth it.
Title: Re: pearse armrest?
Post by: whiskeyjack on June 02, 2006, 06:35:44 PM
I think the smaller the guitar, the more difference you'll hear.
Title: Re: pearse armrest?
Post by: joopie on June 02, 2006, 08:03:54 PM
Denis- are you goin' junior or slimline?

:mellow: J.
Title: Re: pearse armrest?
Post by: Denis on June 03, 2006, 01:59:02 PM
Quote from: joopie on June 02, 2006, 08:03:54 PM
Denis- are you goin' junior or slimline?

:mellow: J.

I think it's both the one I am thinking of buying...junior slimline...:

http://elderly.com/accessories/items/JPA6.htm
Title: Re: pearse armrest?
Post by: DVGuy on June 03, 2006, 03:04:18 PM
Which one fits an L series best?
Title: Re: pearse armrest?
Post by: Denis on June 03, 2006, 03:06:27 PM
Quote from: DVGuy on June 03, 2006, 03:04:18 PM
Which one fits an L series best?

I'm not sure but I ordered the Slimline Junior just a few minutes ago from Elderly for my OM-03SP.

I am curious how much of difference it will make.  I'm going to buff out the satin on the back and sides first, the add the armrest.
Title: Re: pearse armrest?
Post by: joopie on June 03, 2006, 09:53:46 PM
i think i'm gonna go w/ the regular slim- i'll post a pic once it's on...

:mellow: J.
Title: Re: pearse armrest?
Post by: ronmac on June 04, 2006, 08:51:37 AM
Denis, please post some pics when it arrives. I am considering one for my OM.
Title: Re: pearse armrest?
Post by: joopie on June 04, 2006, 10:23:48 AM
put my order in this morning-  :wacko:

:mellow: J.
Title: Re: pearse armrest?
Post by: bob_d on June 04, 2006, 10:30:52 PM
I don't like the idea of adhesives on my Larrivee. I read an article a while back by a luthier, explaining a procedure he uses to repair a crack in the side of a guitar. It might have been Frank Ford but I'm not sure. Anyway, he uses rare earth magnets to hold a temporary brace in place to make the repair. One on the outside and one inside the body.They are very strong little magnets.

If I could attach one or two magnets to the arm rest then use something, a soft piece of cloth or a thin strip of veneer, on the outside of my guitar to protect the finish, then put the other magnet or magnets inside the body of my guitar to hold the arm rest in place without adhesive I might consider buying one.

Sound plausible?

http://www.rare-earth-magnets.com/

Maybe one on each end of the arm rest each paired with another magnet on a flat spot on the insde side of the guitar. Just a thought...
:huh:
Title: Re: pearse armrest?
Post by: ronmac on June 05, 2006, 06:10:46 AM
That is a solution that you could try. It would even make using the armrest on several guitars an option.

I have used the armrest on a few different guitars and have had no finish issues when they were removed, even after a couple of years.
Title: Re: pearse armrest?
Post by: Blue in VT on June 05, 2006, 10:46:12 AM
Well....the armrest on the Parlor just isn't gonna work out... :angry:.  When I play my parlor I find it most comfotable for my arm to rest on the top too far around the lower bout (toward the centerline of the guitar) for the arm rest to fit the curve.  On an my OM it would fit nicely at the top of the lower bout where my arm crosses...but I don't really want on on my purty OM.  So I think this one may be going back...I know a few people have mentioned reshapping them to fit the curve But I think this would be fairly major reconstruction...oh well.  It was a good thought.

Blue
Title: Re: pearse armrest?
Post by: beel on June 05, 2006, 12:04:11 PM
I found this kind of amusing. -- I did a search for John Pearse and found his personal site. On the opening page, he's pictured with a small-bodied guitar with an armrest on it. Then I clicked on "gallery" at the top of the page and it showed me another page with a half dozen photos on it. He's playing 3 different guitars where you can see there's no armrest on them. That's bad for business, isn't it?
Title: Re: pearse armrest?
Post by: Blue in VT on June 05, 2006, 01:24:27 PM
Who has reshapped their arm rests?  How did you do it?  I think it would be pretty serious for my parlor....I'll have to take some pics to illustrate.

Blue
Title: Re: pearse armrest?
Post by: sutton on June 14, 2006, 08:27:29 AM
I got my ebony armrest yesterday for my D 03.  They sent me the junior size not the original that I wanted but I was excited when I saw it decided to use it anyway. The he guitar seems to have a little more punch and it looks nice. Anybody know how much bigger the original is than the junior?  I don't think it's that much.  Any insights are appreciated, anybody else have a junior size on a D model?
Title: Re: pearse armrest?
Post by: Blue in VT on June 14, 2006, 09:26:38 AM
Sutton,
If you check out the JP website you can find printable templates of the different sizes that you can cut out and compare.

Blue
Title: Re: pearse armrest?
Post by: sutton on June 14, 2006, 09:46:20 AM
Thanks Blue!
Title: Re: pearse armrest?
Post by: dcarey on June 14, 2006, 09:48:47 AM
Quote from: Blue in VT on June 05, 2006, 01:24:27 PM
Who has reshapped their arm rests?  How did you do it?  I think it would be pretty serious for my parlor....I'll have to take some pics to illustrate.

Blue

Here's a photo of a John Pearse Slimline Jr. on my parlor.
Did a little reshaping on a belt sander after cutting about 5/8" off the skinny end.

[attachment no longer available]
Title: Re: pearse armrest?
Post by: sutton on June 14, 2006, 10:15:30 AM
Anybody ever try the left hand armrest on their right hand guitars as the JP website suggests?  I think they're trying to say that if you play a dreanought, and pick near the bridge, the left hand model may work better.... :huh:  don't know...
Title: Re: pearse armrest?
Post by: Blue in VT on June 14, 2006, 11:51:39 AM
dcarey,
thanks...shes's acutie...glad to hear that I'm not the only one who needs some mods to their armrest...the placement of yours would work for me if I played in the classical position most of the time...however I typically play in the more standard postion (over my right leg)...and, especially, when I am palm muting my arm crosses the edge of the lower bout pretty far down...see red line in pic....I would also love to have the armrest cover up the dinger on the top and be in position for classical playing as well ...see blue line( similar to you placement).  While the arm rest (as shipped) will fit where the blue line is it can't do both...and the shape is all wrong for the red line location....so.....damn....maybe I should attempt to make my own???

Anyone out there ever make there own armrest?  finding ebony might be hard but I suppose any harwood would probably work...

Blue

[attachment no longer available]
Title: Re: pearse armrest?
Post by: Denis on June 14, 2006, 12:50:29 PM
Just got my slimline junior for my OM about 15-20 minutes ago in the mail.  I'll post a review after it's been on for a few days.  We'll see how much of a difference it makes.  I might get one for the parlor next.
Title: Re: pearse armrest?
Post by: Roman on June 14, 2006, 01:41:41 PM
I don't like the idea of adhesives on my Larrivee.

Well, FYI, that is not a concern . . . especially on your Larrivée.

I've got the armrest on all of my acoustics.  Have removed and replaced, repositioned them on several and there is not an issue regarding any damage to the finish.

In fact, the finish on the Larrivée is one that is the least likely to have damage . . . not from the adhesive (which is a 3M product by the way) but in general.

Guitars are built to last generations, they're not fragile little things . . .
Title: Re: pearse armrest?
Post by: joopie on June 16, 2006, 09:35:15 AM
man, i have been super busy! little time for the guitar :<>...
i did get my armrest and put it on- butttt, i have a problem! it does not sit flush- THERE IS A GAP BETWEEN THE TWO ENDS- i assume it is worped or something- otherwise i love it and it does increase volume! i will try to get pics this weekend w/ my inferior digital...
:mellow: J.
Title: Re: pearse armrest?
Post by: Roman on June 20, 2006, 03:26:16 PM
Here's the one I custom "altered" for my Taylor 814

(http://i58.photobucket.com/albums/g261/mgreek/Taylor814Front1.jpg)